所有類別

維修測試 / 8 個子類別

汽車維修及測試設備

用於洩漏追蹤、目視檢查、電池健康狀況、電路、壓力、火花、油和電氣讀數的診斷工具。

洩漏追蹤煙霧洩漏偵測器更快找到蒸發排放系統、進氣系統、真空系統、排氣系統和密封系統洩漏。視力檢查智慧鉸接式內視鏡利用可控制攝影機移動，檢查氣壓缸、管道、面板和隱藏空間。電池健康電池系統測試儀檢查電瓶、啟動、充電和供電狀況。電路診斷汽車電路測試儀追蹤電源、接地、連續性、短路和元件啟動故障。液位檢查油液分析儀在進行更深入的診斷之前，先評估油品狀況和污染跡象。壓縮引擎壓力測試儀測量汽缸、燃油、真空和壓力性能。點火測試火星塞測試儀更換前請檢查點火火星情況和火星塞性能。電錶汽車診斷萬用電錶讀取電壓、電阻、電流、頻率和汽車訊號。

維修保養 / 6 個子類別

汽車維修保養設備

用於流體交換、空調診斷、冷媒回收、油處理和冷卻系統維修的維修設備。

ATF服務變速箱油液交換器以可控流量更換自動變速箱油。制動液脈動式煞車油交換器使用脈衝壓力沖洗煞車油，以確保排氣順暢。空調壓力表智慧數位歧管壓力表監測冷媒壓力、真空度、溫度和空調數據。空調恢復製冷劑回收機回收、抽真空並重新充注冷媒，以實現可重複的空調服務。石油處理氣動式排油器和抽油器在維修環境中徹底排出並抽取廢油。冷凍服務冷卻系統測試儀和填充器進行壓力測試、真空填充，並排出滯留空氣。

碳清洗 / 3 個子類別

碳沉積物清洗設備

用於清除噴油嘴、進氣閥、零件和車間清潔工作的積碳設備。

噴油嘴試驗台燃油噴射器清潔劑和測試儀清洗噴油嘴並比較噴霧、流量、洩漏和霧化情況。核桃噴砂核桃砂除碳清潔劑使用核桃砂介質清除進氣閥積碳。乾冰清洗乾冰噴射機有效清除積碳、油脂和污垢，並減少殘留物。

車輪輪胎 / 3 個子類別

車輪和輪胎修理設備

用於四輪定位、舉升、輪胎修理、輪胎安裝和服務車間工作流程的設備。

校準3D車輪定位儀測量定位角度並輔助輪胎磨損校正。海灣起重起重設備用於舉升車輛進行底盤、輪胎、煞車和懸吊系統維修。輪胎服務服務輪胎提供輪胎安裝、平衡、維修和日常輪胎保養服務。

工具收納 / 1 個子類別

工作坊工具收納系列

用於整理車間工具、測試設備和配件的收納產品。

店鋪整理工作坊工具存放將診斷工具和維修設備依區域整理存放。

電動車充電 / 1 個子類別

電動車充電器系列

適用於新能源汽車服務、車間使用和安裝場景的電動車充電產品。

新能源電動汽車充電瀏覽適用於車庫和商店的電動車充電產品。

OBD診斷/5個子類別

OBD診斷工具

OBD 相關測試儀、ECU 編程電源、電纜產品、二手車檢測工具和鑰匙頻率診斷。

二手車檢查二手車診斷測試儀檢查二手車並找出隱藏的系統故障。關鍵訊號汽車鑰匙頻率測試儀檢查遙控鑰匙頻率訊號和鑰匙診斷資訊。連接器電纜OBD電纜尋找車輛介面的診斷電纜和連接器。電纜組OBD線線系列瀏覽 OBD 線材系列，尋找適用的型號、轉接器和安裝方式。程式設計能力ECU編程電源在ECU編程和診斷工作期間，保持車輛電壓穩定。

配件 / 8 個子類別

配件

主要診斷和服務設備的替換零件、適配器、耗材、電纜和附加組件。

對準零件3D車輪定位器配件校準機的目標物、夾具、零件和支撐件。洩漏配件煙霧洩漏偵測器配件煙霧測試所需的轉接器、軟管、蓋子和耗材。相機部件汽車偵測攝影機配件攝影機探頭、鉤子、鏡子、電纜和檢查附件。噴油器部件燃油噴射器清潔劑和測試器配件噴油嘴試驗台的轉接器、管路、密封件及維修零件。核桃部件核桃噴砂機配件核桃除碳清洗用噴嘴、軟管、轉接器和零件。乾冰部件乾冰噴射機配件乾冰噴射所需的噴嘴、管道、接頭和支架。空調部件空調冷媒回收及充填機配件空調設備的軟管、接頭、過濾器、配件和維修零件。電池零件電池測試儀配件電池測試儀的夾鉗、電纜、適配器和附加組件。

🔍

AUTOOL SDT208 雙壓汽車煙霧機

額定 4.95 基於5 66 客戶評級

(66 顧客評價）

US$429.00

主要特色

EVAP / Standard Pressure Modes
12/24 V Vehicle Power
壓力和流量監測
空氣+煙霧模式

出貨倉庫

重設

☰ 請求批次/B2B報價

3 年保用期 主機保固 3 年，配件保固 1 年
90日返回 符合條件的退貨可在 90 天內進行
官方店鋪 正品 · 直接支持

AUTOOL SDT208 · 12/24 V Dual-Pressure Smoke Leak Detector

Select EVAP or Standard Pressure Before Smoke Tracing

Choose EVAP or Standard mode only after confirming the vehicle or component procedure and its permitted test pressure. From compatible 12 V or 24 V power, watch pressure and airflow in Air Mode, adjust delivery, then switch to Smoke Mode to trace the visible leak path.

EVAP And Standard Mode Selection
12 V / 24 V Power
壓力和流量回饋
Adjustable Test Delivery
Air Check, Then Smoke Trace

主要特色

Dedicated EVAP and Standard Pressure Controls

Standard and EVAP Pressure Modes

Standard Mode is rated at 35 psi, while EVAP Mode is rated at 10 psi to better protect EVAP lines during testing. Standard Mode supports output up to 35 psi, while EVAP Mode stays below 10 psi. Select either mode only when the vehicle or component service procedure permits that pressure.

Tiny-Leak Checks

EVAP Mode supports controlled repair-shop EVAP checks, including tiny leaks down to about 0.5 mm, while pressure protection helps protect the system under test. After connecting and isolating the system at a permitted pressure, use visible smoke to inspect accessible joints, hoses, and seals for an escape path.

Airflow Meter

The airflow meter helps identify possible leaks by showing changes in airflow.

流量控制閥

The airflow control valve lets you adjust airflow into the test line.

壓力計

The pressure gauge helps identify a possible leak by showing pressure changes.

空氣模式和煙霧模式

The smoke generator supports Air Mode for pressure monitoring and Smoke Mode for visual leak location.

內置氣泵

No external air supply is required. The built-in pump simplifies setup for workshop and mobile repair use.

大約5秒鐘後開始冒煙

The smoke generator produces smoke in about 5 seconds after the power, oil, and test-line setup is complete.

EVAP, Intake and Vacuum-Line Checks

Use this evaporative emission system tester in EVAP Mode, with EVAP tools that match the vehicle test port, to check for leaks. It also helps locate leaks in intake lines, throttle-related lines, vacuum lines, and engine-sealing areas.

Exhaust, Crankcase, Fuel-Tank, Line and Turbo Checks

Supports visual leak checks on exhaust sections, crankcase systems, and line fittings. It can also assist with low-pressure checks around fuel-tank sealing areas and automotive line connections. Use it for selected low-pressure turbo, intercooler, and air-path leak checks within the stated pressure limits.

Visible Oil Level Gauge

The SDT208 interface includes an oil level gauge together with the airflow meter, pressure gauge, power indicator, and alarm indicator.

過熱和低溫保護

Automatic overheat protection shuts off power above 75°C, and the unit supports operation down to -20°C.

3年保固支持

主機：三年保固。標準配件：一年保固。保固政策。

如何使用

Confirm the System, Select Mode, Seal, Test, and Inspect

步驟進展1 / 7

添加測試油

使用前，請在檢測器中註入 10–15 毫升嬰兒油或液體石蠟。切勿過量注入。

安全性和相容性

Never Apply Standard Mode to a Low-Pressure EVAP Task

12V / 24V Power and Built-In Air Pump

Connect SDT208 to a 12V or 24V DC battery before use. The built-in air pump provides the test airflow, so you do not need an external compressor.

Choose the Pressure Mode Before Testing

Use EVAP Mode for EVAP-focused testing below 10 psi. Standard Mode is available up to 35 psi, but select it only when the vehicle or component service procedure permits that pressure range.

Use the Oil-Level Gauge, but Keep the 10–15 mL Fill Limit

Testing oil is not included. Use liquid paraffin or baby oil, add 10–15 mL before use, and use the oil-level gauge to check the current oil volume without overfilling.

連續使用時間限制為 8 分鐘

Do not run SDT208 continuously for more than 8 minutes. Automatic overheat protection shuts the unit down above 75°C. Let the unit cool before restarting.

Operating Temperature and Hot Surfaces

SDT208 supports operation down to -20°C. The round metal housing can become hot during use, so avoid touching hot surfaces directly.

請勿用於直接高壓空調測試

Standard Mode can reach up to 35 psi, but SDT208 still cannot directly pressure-test an automotive A/C high-pressure system. If a service procedure permits smoke on an isolated A/C line section, use smoke only as an indirect visual aid.

Match the Adapter and Test Procedure to the System

Use the correct adapter and pressure mode for the selected system. Follow the vehicle or component service procedure, and do not introduce smoke or pressure where the procedure does not permit it.

Trace the Leak with Smoke

Use visible smoke to trace the leak area. If no smoke appears, recheck isolation, flow, and the test setup before continuing.

切勿在運作過程中加油

SDT208 運轉時請勿添加測試油。

Respect Selected Mode Limits

Use pressure and airflow controls only within the selected mode’s permitted range.

Cool Before Restarting

Let the unit cool before restarting after overheat protection is triggered.

檢測結果

Interpret Pressure, Flow, and Smoke by Selected Mode

Use Pressure and Flow to Guide Inspection

Use the pressure gauge and flow meter to assess system behavior and guide the next leak-inspection step.

可見煙霧逃逸

檢查該插座是否為故意開口，然後檢查、修復並重新測試該區域。

沒有可見煙霧

在進行功能性診斷或其他測試方法之前，請先確認通道暢通、隔離、閥門狀態和煙霧輸送。

比較型號

Compare Pressure Modes and Vehicle Power

相對比 AUTOOL 煙霧洩漏偵測器
產品描述*	SDT50	SDT60	SDT100	SDT101	SDT102	SDT103	SDT106	SDT203	SDT205	SDT205S	SDT206	SDT208
煙霧輸出與防護
工作原理	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒	低氧燃燒
測試油填充量	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml	10-15ml
額定輸出壓力	＜10psi	＜10psi	＜10psi	3.2千帕（0.46磅/平方英吋）	＜10psi	3.2千帕（0.46磅/平方英吋）	＜12psi	＜15psi	＜15psi	＜15psi	＜18psi	<10 psi / 35 psi machine modes; select by the vehicle procedure.
額定輸出流量	＜5公升/分鐘	＜5公升/分鐘	＜5公升/分鐘	> 10L / min	＞ 6L / min	> 10L / min	＜5公升/分鐘	＜6公升/分鐘	＜6公升/分鐘	＜6公升/分鐘	＜6公升/分鐘	＜15公升/分鐘
高溫保護	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作	溫度高於75°C時停止工作
響應時間	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧	5秒內產生煙霧
功率和物理尺寸
輸入功率	DC12V	DC12V	DC12V	DC12V / 5A	DC12V	DC12V / 5A	DC12V	DC12V	DC12V	DC12V	DC12V	DC12V / 24V
額定功率	50W	50W	50W	48W	48W	48W	50W	65W	65W	65W	70W	80W
淨重（主機）	1.5kg	1.6kg	1.6kg	1.6kg	1.6kg	1.15kg	3.5kg	1.7kg	3.2kg	3.2kg	3.5kg	4.2kg
主機尺寸	145mm * 80mm * 200mm	145mm * 80mm * 200mm	180mm * 102mm * 143mm	180mm * 100mm * 135mm	180mm * 102mm * 143mm	180mm * 100mm * 135mm	110mm * 135mm * 210mm	145mm * 80mm * 200mm	295mm * 295mm * 207mm	295mm * 295mm * 207mm	150mm * 150mm * 275mm	350mm * 250mm * 300mm
監控與控制
流量計視窗	×	×	×	×	×	✓	×	✓	×	✓	✓	✓
壓力計	×	✓	×	×	✓	×	×	✓	✓	✓	✓	✓
空氣源類型	內置氣泵	內置氣泵	內置氣泵	外部空氣源	內置氣泵	外部空氣源	內置氣泵	內置氣泵	內置氣泵	內置氣泵	內置2個氣泵	內置氣泵
模式輸出	煙霧模式	煙霧模式	煙霧模式	煙霧模式	煙霧模式	煙霧模式	煙霧模式	煙霧模式	空中模式煙霧模式	空中模式煙霧模式	空中模式煙霧模式	空中模式煙霧模式
雙壓力模式	×	×	×	×	×	×	×	×	×	×	×	標準 35 psi / EVAP 10 psi 機器模式；使用車輛程序。
流量調節旋鈕	×	×	×	×	×	✓	×	✓	×	✓	✓	✓
放油閥	×	×	×	×	×	×	×	×	✓	✓	✓	✓
故障指示燈	×	×	✓	×	✓	×	×	✓	✓	✓	✓	✓
油位計	×	×	×	×	×	×	×	×	×	×	✓	✓

使用者手冊及下載

請參考手冊進行設定和測試壓力

手冊/PDF

AUTOOL SDT208 使用手冊

Open the PDF manual for SDT208 EVAP and Standard pressure modes, 12/24 V setup, pressure and flow control, test safety, and troubleshooting.

快速入門指南

小包裝

產品包括

主機AUTOOL SDT208 煙霧洩漏偵測器
電力電纜12V / 24V battery power cable
煙霧軟管Smoke output hose for leak testing
適配器Cone adapter, rubber caps, adapter set, and accessories
油瓶Empty oil bottle included; testing oil is not included
文档User manual, warranty information, certificate, and retail box

常見問題

EVAP Mode, 12/24 V, and Pressure Questions

SDT208 應該使用哪一種測試油？

本產品不含測試油。如果無法取得專用煙霧測試油，請使用液體石蠟或嬰兒油代替。

我應該添加多少測試油？

Add 10–15 mL testing oil before use. Do not add more than 15 mL each time. Refill only when the smoke becomes thin, and drain the remaining testing oil before adding fresh oil. If too much oil is added accidentally, drain some oil out before operation.

SDT208 需要什麼樣的電源？

SDT208 requires a 12V or 24V DC battery. Connect the detector to the battery correctly before turning on the unit.

SDT208 能偵測 EVAP 洩漏嗎？

Yes. SDT208 can be used for EVAP leak checks. Use EVAP Mode with the EVAP adapter or service tool that matches the vehicle test port.

What Is the Difference Between Standard Mode and EVAP Mode?

Standard Mode supports testing up to 35 psi. Use it only for systems whose service procedure allows that pressure range. EVAP Mode is limited below 10 psi to help protect EVAP lines during testing. Always select the mode according to the system being tested.

SDT208可以直接偵測汽車空調系統洩漏嗎？

No. The automotive A/C system operates at about 1.7–3.0 MPa output pressure, while smoke leak detectors generate much lower pressure. SDT208 cannot directly pressure-test the automotive A/C system for leaks. Use smoke only to help inspect an A/C line section after isolating and pressurizing it according to the service procedure.

如何利用煙霧來定位獨立空調管路部分的洩漏點？

首先，依照車輛或空調維修程序，隔離並加壓空調管路段。然後在測試段附近噴灑煙霧，觀察逸出的氣流是否會擾動煙霧。如果逸出的氣流帶動煙霧流動，則檢查該區域是否有洩漏。

SDT208 可以測試哪些系統？

SDT208 supports low-pressure leak checks on EVAP, intake, exhaust, crankcase, fuel-tank, vacuum-line, vehicle-sealing, and line-fitting systems. For selected turbo or intercooler paths, SDT208 can also be used as a turbo smoke tester. Standard Mode is available up to 35 psi, but use it only when the vehicle or component service procedure allows that pressure range.

How Do I Read the Pressure Gauge and Flow Meter?

Use the pressure gauge and flow meter to monitor pressure and airflow during the test. In general, if the pressure gauge continues to rise and stabilize, the test line may have no obvious leak. If the pressure continues to decrease, the line may have a leak that needs further inspection and repair.

我可以調節SDT208的壓力嗎？

SDT208 provides Standard Mode and EVAP Mode, plus airflow adjustment through the regulator. It is not designed as an unrestricted high-pressure tester. Use the pressure mode specified for the selected system, and do not apply smoke pressure where the vehicle or component service procedure excludes smoke testing.

包含哪些配件？

Check the product listing or your selected package option for the exact items included. The package includes the main unit, power cable, smoke hose, adapters, rubber caps, oil bottle, manual, warranty information, certificate, retail box, and other listed accessories. Testing oil is not included.

What Should I Check If the Smoke Becomes Thin or No Smoke Appears?

First check that the detector contains 10–15 mL of testing oil. Confirm that the power supply is connected, the airflow regulator is open, and the correct switch and mode are selected. If smoke becomes thin, drain the remaining oil and add fresh testing oil. If the detector has overheated, let it cool before restarting. Contact support if the issue remains.

怎麼辦 AUTOOL 煙霧洩漏偵測器型號有何不同？

外部空氣蒸發器：SDT101/103 — 3.2 kPa (0.46 psi)。
內建泵浦：SDT106 <12 psi；SDT203/205/205S <15 psi；SDT206 雙泵浦 <18 psi。
SDT208: 35 psi Standard / 10 psi EVAP.

Also compare power supply, flow monitoring, oil drainage, and accessories.

How Long Is the Warranty?