語言和貨幣
AUTOOL SML330 汽車煙霧洩漏偵測器
US$799.00
主要特色
- Adjustable Smoke Flow
- 空氣+煙霧模式
- 內置氣泵
- 可視壓力表
- Adjustable Smoke Flow: Turn the flow control while watching the flow window to match delivery to the sealed test volume.
- 空氣+煙霧模式： Use an air-only pressure stage before switching to smoke for visual localization.
- 內置氣泵： Supply test airflow without a separate shop-air compressor.
- 可視壓力表： Watch pressure behavior while filling the connected volume, then inspect unstable or falling readings with smoke.
- Oil Drain Valve: Drain aged or excess smoke oil before refilling or storage.
- 3 年保用期 主機保固 3 年，配件保固 1 年
- 90日返回 符合條件的退貨可在 90 天內進行
- 官方店鋪 正品 · 直接支持
AUTOOL SML330 · Adjustable-Flow Automotive Smoke Leak Detector
Tune Smoke Flow for the Prepared Test Volume
Adjust smoke delivery while watching the flow window to match the sealed test volume, then use an air-only pressure stage before switching to smoke for visual localization. The built-in pump, pressure gauge, and oil drain valve support permitted low-pressure checks without a separate shop-air compressor.
- 獨立的空氣和煙霧模式
- 內建泵，無需車間氣源
- 壓力和流量回饋
- Adjustable Smoke Flow
- 放油閥
主要特色
Adjustable Smoke Flow with Pressure Monitoring
Air and Smoke Modes
Use Air Mode for pressure and flow checks before switching to Smoke Mode for visual leak location, following the model controls and system procedure.
內置氣泵
The internal pump supplies test airflow, so routine setup does not require a separate shop-air compressor.
可視壓力表
Watch pressure behavior while the connected volume fills, then use Smoke mode to inspect an unstable or falling reading.
Adjustable Smoke Flow
Turn the flow control gradually while watching the flow window to suit the size of the sealed test volume.
放油閥
Empty aged or excess smoke oil through the drain valve before refilling or storing the machine.
Smoke in About 5 Seconds
Smoke starts in about five seconds after the prepared system is connected and the mode is activated.
Overheat Shutdown Above 75°C
Temperature protection stops operation when the model reaches its protection condition; allow the unit to cool before further use.
65W Rated Power
The 65 W rating works with the specified 12 V / 5 A supply; use a stable vehicle-battery connection.
3年保固支持
主機：三年保固。標準配件：一年保固。保固政策。
如何使用
Seal, Check with Air, Adjust Smoke, and Inspect
步驟進展1 / 6
01
Confirm the Procedure
Identify the target system, permitted pressure or threshold, access point, valve state and openings that must be sealed.
02
準備機器
Inspect the power lead, air connection where required, hose and adapters. Add or confirm only the smoke oil specified by the manual.
03
Connect and Isolate
Use the correct adapter, make a leak-free connection to the selected test point, and isolate normal escape paths according to the vehicle procedure.
04
Run Air or Pressure Mode
Use Air Mode first and observe the pressure gauge and flow window under the selected test conditions.
05
Use Smoke to Inspect
Switch to Smoke mode when visual tracing is needed, allow the connected volume to fill, and inspect accessible joints, hoses and seals for escaping smoke.
06
Repair and Retest
Repair the confirmed escape path, repeat the same controlled test, and continue with functional diagnosis if the result is inconclusive or no smoke is visible.
安全性和相容性
Match Pressure, Flow, Medium, and Procedure
Match Pressure to the System
The machine rating is not permission to apply its maximum to every vehicle system. Use the OEM or component procedure and the lowest appropriate controlled setting.
Confirm Air and Power
Connect SML330 to a stable DC 12 V / 5 A supply. Its built-in pump provides airflow; do not connect shop air to an unspecified port.
Protect People and Components
Work in a dry, well-ventilated area away from flame and hot sources; use eye and hand protection and avoid directing smoke at smoke-sensitive or precision electronic parts.
Inspect Hoses and Adapters
Do not operate with damaged power leads, hoses or adapters. Clean an opening before inserting an inflatable airbag so sharp edges do not puncture it.
Use Approved Smoke Machine Fluid
Follow the model manual for fluid selection, fill level, draining and storage. Do not use water, viscous or corrosive liquids.
Interpret Results Carefully
Pressure-gauge or flow-window changes and escaping smoke support the next inspection step. No result alone rules out incorrect isolation, blockage, valve-control, intermittent, or non-leak faults.
檢測結果
Read Pressure and Smoke at the Correct Test Stage
Pressure Holds Within the Specified Limits
When pressure holds within the selected vehicle or component procedure limits, record the result for that setup. If it falls outside the threshold, continue with flow and smoke inspection.
Pressure Drops or Exceeds the Procedure Limit
Check the machine self-test, connection and intentional openings, then use smoke to inspect for an escape path.
Smoke Escapes
Confirm the smoke is not leaving a normal open route, repair the verified leak and repeat the same test.
No Smoke Is Visible
Recheck setup and isolation, then investigate valve control, blockage, intermittent behavior or a non-leak cause as the vehicle procedure directs.
比較型號
Compare Smoke-Flow Controls
模型指南
Choose one or more models. SML330 is selected by default.
已選擇 1 個模型
未選擇任何型號。請選擇一個型號進行比較。
| 產品描述* | SML310 | SML330 | SML400 | SML500 |
|---|---|---|---|---|
| Operating specifications | ||||
| 工作原理 | 低氧燃燒 | 低氧燃燒 | 沒有說明 | 沒有說明 |
| 輸入功率 | DC 12V / 5A | DC 12V / 5A | 直流12V | Confirm the selected regional power configuration |
| 測試油填充量 | 10ml | 10ml | 沒有說明 | 沒有說明 |
| 額定輸出壓力 | ＜15psi | ＜15psi | 沒有說明 | 沒有說明 |
| 額定輸出流量 | ＜6公升/分鐘 | ＜6公升/分鐘 | 沒有說明 | 沒有說明 |
| 額定功率 | 65W | 65W | 沒有說明 | 沒有說明 |
| 高溫保護 | 溫度高於75°C時停止工作 | 溫度高於75°C時停止工作 | 沒有說明 | 沒有說明 |
| LOW-Temperature Protection | Confirm the operating-temperature limit for the selected unit. | Confirm the operating-temperature limit for the selected unit. | 沒有說明 | 沒有說明 |
| Hardware and air supply | ||||
| 流量計視窗 | × | × | 沒有說明 | 沒有說明 |
| 淨重（主機） | 3.2kg | 3.2kg | 沒有說明 | 沒有說明 |
| 主機尺寸 | 250mm * 160mm * 165mm | 250mm * 160mm * 165mm | 沒有說明 | 沒有說明 |
| 壓力計 | 測量 | 測量 | 沒有說明 | 沒有說明 |
| 空氣源類型 | 內建泵浦 | 內建泵浦 | 內建泵浦 | Confirm the selected unit’s required air connection |
| Modes and controls | ||||
| 模式輸出 | Air Mode/Smoke Mode | Air Mode/Smoke Mode | 沒有說明 | 沒有說明 |
| 雙壓力模式 | × | × | 沒有說明 | 沒有說明 |
| 流量調節旋鈕 | × | √ | 沒有說明 | 沒有說明 |
| 放油閥 | × | × | 沒有說明 | 沒有說明 |
| 故障指示燈 | × | × | 沒有說明 | 沒有說明 |
| 油位計 | × | × | 沒有說明 | 沒有說明 |
| 設定與控制 | ||||
| 控制級別 | Gauge, Air/Smoke | Gauge + flow adjustment, Air/Smoke | TFT + fixed pressure-hold routine + flow controls | Touchscreen configurable pressure-hold and smoke workflow |
使用者手冊及下載
請參考手冊進行設定和測試壓力
AUTOOL SML330 User Manual
Open the PDF manual for SML330 Air and Smoke modes, pressure and flow monitoring, output adjustment, smoke-oil draining, safety, and troubleshooting.
小包裝
產品包括
- Confirm Your PackageIncluded accessories can vary by order. Confirm the main unit, 12 V power lead, smoke hose, adapters, sealing tools, oil bottle and quantities before checkout.
常見問題
Flow Adjustment and Pressure Questions
What air source does SML330 use?
It has a built-in air pump, so normal testing does not require a separate shop-air compressor.
Can I use the maximum pressure on an EVAP system?
Do not assume so. Choose pressure from the vehicle procedure; machine capacity and EVAP-safe pressure are different facts.
What Does Air Mode Tell Me?
利用配置好的密封測試裝置下的壓力和流量行為來指導下一步的洩漏檢測步驟。
What does Smoke mode add?
Smoke gives a visible tracer for inspecting an escape path after the test volume is connected and isolated correctly.
What if no smoke is visible?
Verify smoke delivery, access, isolation, adapter sealing and valve state. Then continue with the applicable functional diagnosis because blockage, intermittent or non-leak faults may not produce visible smoke.
Are all pictured accessories included?
Package contents vary by order. Confirm every included item and quantity before checkout.
Does a visible leak guarantee the entire repair?
It identifies an area to inspect and confirm. Repair the verified problem and repeat the test, then complete any required vehicle checks.
客戶評價
留言
還沒有評論率先分享您使用此產品的體驗。