語言和貨幣
AUTOOL CT400 四缸燃油噴射器清洗測試儀
原價為：575.00 美元。US$509.00目前價格為：509.00 美元。
主要特色
- GDI / EFI / FSI Drive
- Six-Injector Comparison
- Clean, Test + Recheck
- Integrated Digital Controls
- GDI / EFI / FSI Drive: Select 12 V, 70 V, or 120 V injector drive for compatible standard gasoline, EFI, FSI, and selected GDI injectors.
- Six-Injector Comparison: Mount up to six compatible injectors to compare spray appearance and collected volume under the same setup.
- Clean, Test + Recheck: Use ultrasonic cleaning and permitted reverse flushing, then repeat leakage, spray, and volume observations under matched conditions.
- Integrated Digital Controls: Set function, time, pulse, voltage, and pressure from one panel for a repeatable bench setup.
- 2,000 mL Tank + Drawer: A 2,000 mL ultrasonic tank supports batch cleaning, while the drawer organizes adapters, plugs, cables, and seals.
- 3 年保用期 主機保固 3 年，配件保固 1 年
- 90日返回 符合條件的退貨可在 90 天內進行
- 官方店鋪 正品 · 直接支持
AUTOOL CT400 · Six-Position Multi-Drive Injector Bench
Drive and Compare Selected Injectors at Three Voltages
Ultrasonically clean compatible standard gasoline, EFI, FSI and selected GDI injectors, then compare up to six for spray, leakage and collected volume under matched low-pressure conditions. Select 12 V, 70 V or 120 V drive to match supported injector requirements. A 2 L cleaning tank, 3 cleaning and 9 test functions, adjustable bench controls and storage drawer support organized clean-and-retest work.
- EFI / FSI / 選定的 GDI
- 四位噴油嘴對比
- 12/70/120伏特驅動器
- 2 L Ultrasonic Cleaning Tank
- 3 Cleaning + 9 Test Functions
主要特色
Selectable Injector Drive with Six Test Positions
相容的標準和直接噴射服務
This fuel injector tester cleans and performs low-pressure comparative checks on compatible standard gasoline, EFI, FSI, and selected GDI injectors when the correct adapter, connector, electrical drive, seal set, and procedure are available.
12 V / 70 V / 120 V Selection
選擇 12V、70V 或 120V 驅動，以符合噴油嘴類型及其運作要求。
六位並排測試
Mount up to six compatible injectors to compare spray appearance and collected volume under the same setup. Plug all unused positions when testing fewer injectors.
3 Cleaning and 9 Testing Functions
Use ultrasonic cleaning, reverse flushing where permitted, optional on-vehicle cleaning with separately required accessories, leakage checks, spray-pattern modes, and preset low-pressure operating cycles.
Ultrasonic Injector Cleaning with Pulse Drive
Pulse actuation and ultrasonic energy work with an approved cleaning fluid to loosen deposits; cleaning outcome must be checked by repeating the same observation cycle afterward.
2,000毫升清洗罐
This fuel injector cleaning machine has a 2,000 mL ultrasonic tank for batch cleaning before matched low-pressure comparison; follow the supplied manual for the working fill level and fluid limits.
Spray, Volume, and Leakage Observation
Compare closed-injector drips, spray shape and collected volume in the measuring cylinders to guide triage and matched group comparison.
Reverse Flushing for Applicable Injectors
Reverse flushing can help move contamination from compatible top-feed injectors or strainers; confirm that the injector design and manufacturer procedure permit it before use.
Integrated Digital Controls
Select the function and set the supported time, pulse, voltage, and pressure controls from one panel for a more repeatable bench setup.
液體排放和回收
Use the drain path to empty or recover the appropriate fluid as instructed, keeping ultrasonic cleaning fluid separate from the testing circuit.
Accessory Storage Drawer
Keep adapters, plugs, cables, seals, and small fittings organized near the work area to reduce setup delays and misplaced parts.
Optional Cleaning Without Injector Removal
The machine supports an optional on-vehicle cleaning workflow only with the specified special adapters; those accessories and the vehicle-specific procedure must be confirmed separately.
3年保固支持
主機：三年保固。標準配件：一年保固。保固政策。
如何使用
Identify the Injector, Select Drive, Clean, Test, and Compare
步驟進展1 / 7
01
Identify the Injector and Service Scope
Record the manufacturer and part number; confirm standard gasoline, EFI, FSI, or selected GDI applicability, electrical drive, feed direction, cleaning permission, replacement seals, and whether CT400’s low-pressure comparison is suitable for the job.
02
Select the Correct Adapter and Drive
Choose the correct connector, rail adapter and plugs, then select voltage for the injector type. If the setting is uncertain, start at 12 V and increase gradually to 70 V and then 120 V until the injector operates correctly. Avoid prolonged operation at an incorrect high voltage.
03
加入認可的清潔液
Fill the ultrasonic tank with a cleaning fluid approved for the injector and machine. Never operate the ultrasonic function dry, and do not assume every injector permits ultrasonic cleaning.
04
進行超音波清洗
Connect the pulse lead, secure the injectors, and run the selected cleaning cycle according to the manual. Treat cleaning as a controlled process whose effect must be checked afterward.
05
Mount Injectors for Testing
Install up to six compatible injectors with the correct seals and fittings. Verify clamping and channel sealing; plug every unused measuring position before pressurizing the test circuit.
06
Add Test Fluid and Configure the Test
Use approved non-corrosive injector test fluid in the test circuit, then set the documented drive, pressure, pulse, time, and selected low-pressure test mode. Keep cleaning and testing fluids separate.
07
Observe, Repeat, and Recover Fluid
Compare leakage, spray appearance, and collected volume under identical settings; swap channels when needed to rule out fixture or channel error. Repeat the same test after cleaning, then drain or recover fluids as instructed.
安全性和相容性
Confirm Electrical Drive, Adapter, Fluid, and Pressure
Low-Pressure GDI Boundary
CT400 may clean and comparatively observe selected compatible GDI injectors at bench pressure; it is not a professional high-pressure GDI characterization, coding, or calibration system.
Verify Part-Number Compatibility
Match the injector part number, electromagnetic or other drive type, connector, polarity, adapter, feed direction, seals, permitted pressure and cleaning method. Select the voltage using the procedure in Step-by-Step Workflow.
使用經批准的測試液
Use the non-corrosive injector test fluid specified for the machine and application. Do not use gasoline or corrosive cleaning solution in the test circuit.
使用認可的清潔液
Use an ultrasonic cleaning fluid permitted by both the injector manufacturer and CT400 instructions. Do not run the ultrasonic tank without fluid.
Keep Fluids Separate
Cleaning and testing fluids have different duties and material risks. Keep them in their assigned circuits and follow the applicable safety data, ventilation, ignition-control, handling, and disposal requirements.
Secure and Seal the Fixture
Install the correct seals and fittings, secure the rail, inspect for leaks, and plug unused positions before applying pressure. Replace one-time seals or clips when the vehicle procedure requires it.
有條件反向清洗和車用清洗
Use reverse flushing only on compatible feed designs. Cleaning without injector removal requires special adapters and a vehicle-specific procedure; it is not included merely because the mode appears on the panel.
柴油機服務限制
CT400 can ultrasonically clean compatible diesel injectors when their approved procedure permits it. Diesel opening-pressure, spray, common-rail, return-flow, coding, and calibration tests require dedicated equipment.
檢測結果
Read Spray, Leakage, and Volume Under One Setup
關閉時滴水
First check the adapter, seal, rail, and channel for leakage. If the injector itself continues to drip after an approved clean-and-retest cycle, seat wear or an internal fault may require specialist evaluation or replacement.
一個氣缸收集的液體較少
A lower collected volume can indicate restriction, but it can also come from a mounting leak, unstable setup, or channel issue. Verify pressure and sealing, swap channels, then repeat under the same settings before judging the injector.
Uneven or Coarse Spray
Deflected, split, coarse, or dripping spray may reflect deposits or internal damage. Repeat after permitted cleaning; if the pattern remains abnormal, continue with injector-specific service or replacement guidance.
清潔後差異縮小
A smaller group difference under the same conditions suggests that a removable restriction may have been reduced. Record the settings and result, fit required new seals, and verify the repair on the vehicle.
No Meaningful Change
The injector may already be clean, the deposit may not be recoverable, or an electrical or mechanical fault may be present. Avoid repeated uncontrolled cleaning and continue diagnosis.
Balanced Bench Result, Vehicle Fault Remains
The cause may be outside the injectors. Check vehicle fuel pressure, control signals, wiring, ignition, compression, intake leakage, and other relevant systems using the service procedure.
Use Bench Results with Injector Specifications
Use CT400 to compare supported injectors under matched low-pressure settings. Use injector-specific limits and dedicated equipment for OEM calibration, coding, or original-pressure GDI leakage and delivery checks.
比較型號
Compare Injector Drive and Heating Options
模型指南
選擇一個或多個型號。預設選擇 CT400。
已選擇 1 個模型
未選擇任何型號。請選擇一個型號進行比較。
| 產品描述* | CT150 | CT160 | CT200 | CT400 | CT450 | CT500 | FN602 | FN603 | FN606 | FN608 |
|---|---|---|---|---|---|---|---|---|---|---|
| 設定與控制 | ||||||||||
| 輸入電壓 | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V | 110 / 220V |
| 脈衝設定 | 0-20ms | 0-20ms | 0-20ms | 0-20ms | 0-20ms | 0-40毫秒，步長0.1毫秒 | 0-20ms | 0-20ms | 0-40毫秒，步長0.1毫秒 | 0-40毫秒，步長0.1毫秒 |
| 時間設定範圍 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 | 0-10分鐘 |
| 類比轉速範圍 | X | X | X | X | X | X | X | X | X | X |
| 支援的電壓設定 | 固定 12V 驅動；無 12/70/120V 可選模式 | 固定 12V 驅動；無 12/70/120V 可選模式 | 固定 12V 驅動；無 12/70/120V 可選模式 | 12V 70V 120V | 12V 70V 120V | 12V 70V 120V | 12V 70V 120V | 12V 70V 120V | 12V 12V-70V 120V-180V | 12V 12V-70V 120V-180V |
| 語言設定 | × | × | × | × | × | 2 種類型（中文、英文） | × | × | 2 種類型（中文、英文） | 2 種類型（中文、英文） |
| 壓力表顯示 | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| LCD顯示器 | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| 清潔和流體系統 | ||||||||||
| 試管體積 | 110ml | 100ml | 110ml | 110ml | 110ml | 110ml | 100ml | 110ml | 110ml | 110ml |
| 清洗槽容積 | 1000ml | 2000ml | 1700ml | 2000ml | 2000ml | 請確認您訂單所需的油箱容量 | 2000ml | 2000ml | 550ml | 550ml |
| 超音波清洗能力 | 70w | 70w | 70w | 70w | 70w | 70w | 70w | 70w | 70w | 70w |
| 內建泵浦 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 2 |
| 清潔液加熱 | × | ✓ （45℃） | × | × | ✓ （50℃） | × | ✓ （45℃） | ✓ （45℃） | ✓ （50℃） | ✓ （50℃） |
| 測試液位計 | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| 清洗液回收閥 | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| 可拆卸清洗槽 | × | × | × | × | × | × | ✓ | × | ✓ | ✓ |
| 燃油幫浦數量 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 2 |
| 功能和噴油器覆蓋範圍 | ||||||||||
| 基本功能 | 3種清潔功能 9 測試功能 | 3種清潔功能 9 測試功能 | 3種清潔功能 9 測試功能 | 3種清潔功能 9 測試功能 | 3種清潔功能 10 測試功能 | 3種清潔功能 12 測試功能 | 3種清潔功能 10 測試功能 | 3種清潔功能 10 測試功能 | 3種清潔功能 12 測試功能 | 3種清潔功能 12 測試功能 |
| 適配器連接器 | 3類型 | 5類型 | 3類型 | 9類型 | 9類型 | 9類型 | 9類型 | 9類型 | 9類型 | 9類型 |
| 噴油嘴測試位置 | 4 燃油噴射器 | 4 燃油噴射器 | 6 燃油噴射器 | 6 燃油噴射器 | 6 燃油噴射器 | 6 燃油噴射器 | 4 燃油噴射器 | 6 燃油噴射器 | 6 燃油噴射器 | 8 燃油噴射器 |
| 燃油噴射器清洗類型 | 標準燃油噴射器 | 標準燃油噴射器 | 標準燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 | 標準燃油噴射器 GDI、EFI、FSI 長燃油噴射器 |
| 支援低阻抗噴油器 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 | 僅限相容型號；請確認噴油嘴零件號碼和驅動要求 |
| 操作與設備 | ||||||||||
| 油擋板設計 | × | × | × | × | × | ✓ | ✓ | ✓ | ✓ | ✓ |
| 運行工況模擬測試 | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
| 儲物抽屜 | × | × | × | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
使用者手冊及下載
請參考手冊了解設定和測試模式。
AUTOOL CT400 使用手冊
Open the PDF manual for CT400 ultrasonic cleaning, injector voltage selection, six-position spray and volume tests, reverse flushing, safety, and troubleshooting.
小包裝
產品包括
- 主機AUTOOL CT400 six-position fuel injector testing machine with ultrasonic cleaning.
- Injector Adapters and ConnectorsAdapter sets, connector parts, fittings, sealing rings, and related hardware.
- Test Setup PartsFuel-rail and measuring-cylinder parts, signal harnesses, and locking hardware used by the included configurations.
- 五位插頭Five plugs for sealing unused positions during single-injector testing.
- 流體處理部件Funnel, drain-related parts, ultrasonic-tank cover, and associated fittings.
- Documentation and PowerUser manual and power cable; plug and voltage configuration must match the ordered regional version.
常見問題
Drive, Fit, and Test Questions
CT400能否在原引擎壓力下測試GDI噴油嘴？
CT400 drives, cleans, and compares selected compatible GDI injectors under low-pressure bench conditions. Use dedicated high-pressure equipment for original-engine GDI verification, OEM calibration, or coding.
How many injectors can CT400 handle?
It has six injector positions. When testing fewer than six, securely plug every unused test position; five plugs are supplied for single-injector testing.
How do I select 12 V, 70 V, or 120 V?
Select voltage according to the injector type. If the setting is uncertain, start at 12 V and increase gradually to 70 V and then 120 V until the injector operates correctly; an incorrect setting may result in no injection or a machine alarm.
What can I compare on the bench?
Under identical setup conditions, you can compare closed-injector leakage, spray appearance, collected volume, and response during the available low-pressure cycles. Use injector-specific limits only when the test procedure and conditions match.
可以 AUTOOL CT Series Products Clean And Test Diesel Injectors?
AUTOOL CT series products can clean diesel injectors, but they cannot test diesel injectors. If diesel injector testing is required, confirm the correct dedicated equipment before ordering.
- No. Compatible diesel injectors may be ultrasonically cleaned when their approved procedure permits it, but diesel testing requires dedicated mechanical or common-rail equipment, depending on injector type.
我可以用清洗液測試噴油嘴嗎？
No. Cleaning fluid is corrosive and may damage internal machine components, corrode rubber parts, and cause leakage. Use professional injector test fluid for testing. If equipment is damaged because cleaning fluid is used during injector testing, repair costs may need to be borne by the user.
- No. Use approved cleaning fluid in the ultrasonic tank and approved non-corrosive injector test fluid in the testing circuit. Do not use gasoline or mix the fluids.
Does CT400 heat the cleaning tank?
No. CT400 does not heat the cleaning tank. Choose a model with documented heating if the approved cleaning process requires it.
Can I reverse-flush every injector?
No. Reverse flushing is only for compatible injector designs, such as applicable top-feed units or strainers, and must be permitted by the injector service procedure.
Can CT400 clean injectors without removal?
Yes, as an optional procedure with the required special adapters. Confirm the accessory set, vehicle procedure, fluid, and safety requirements before use.
What should I do if one channel reads low?
Check the fixture, seals, pressure stability, and channel first. Swap positions and repeat under the same settings before deciding that the injector is restricted.
什麼是保修？
主機：三年保固。標準配件：一年保固。保固政策。
我該如何選擇測試液？
Test fluid is used to evaluate fuel injector performance. Use the injector test fluid specified in the product manual to simulate test conditions consistently. For consistent results, use professional automotive injector test fluid. If unavailable, medical alcohol with over 75% alcohol content can be used as an alternative.
How Should I Choose Cleaning Fluid?
Cleaning fluid removes carbon deposits from fuel injectors and is typically corrosive and flammable. For consistent results, use professional ultrasonic cleaning fluid or professional engine carbon cleaning fluid. If unavailable, 75%+ medical alcohol can be used as a substitute, but cleaning performance may vary.
Do I Need To Add Fluid Before Ultrasonic Cleaning?
Yes. Before using the ultrasonic cleaning function, add the professional carbon cleaning fluid first. Do not run the ultrasonic tank dry; doing so may damage the ultrasonic system.
How Do I Set Test Parameters On CT400?
You do not need complicated special settings. Select the injector type and test function, then set the required voltage, pressure, time, and pulse parameters.
How Do I Select The Correct Voltage When Testing GDI Injectors?
Select the voltage according to the injector type. If you are unsure, gradually increase the voltage from 12V to 70V to 120V until the injector functions correctly. If the voltage selection is incorrect, there may be no fuel injection or the machine may alarm.
Will The Wrong Voltage Damage A GDI Injector?
Short-term incorrect voltage usually will not immediately damage the injector. However, do not apply incorrect high voltage to an injector for a long time. If the injector does not work properly, adjust to the correct voltage in time.
如何使用 CT400 測試單一噴油嘴？
When testing a single injector, plug the other five cylinders. CT400 comes with five plugs for this purpose.
CT200 和 CT400 有什麼不同？
CT200 only supports 12V standard fuel injectors. CT400 supports both 12V standard injectors and GDI injectors, making it compatible with a wider range of injector types and vehicles. CT200 does not have dedicated accessory storage, while CT400 includes a drawer for injector adapters and other accessories.
CT400、CT450 和 CT500 有什麼不同？
Compared with CT400, CT450 adds the Pulse Injection Test. Compared with CT450, CT500 further adds Wide Pulse Injection Test and Continuous Injection Test for more advanced injector testing. For cleaning, CT450 features ultrasonic cleaning with heating up to 50°C, while CT400 and CT500 do not have a heating function.
FN608 和 FN606 有什麼不同？
FN608 supports testing for 8 cylinders, while FN606 supports testing for 6 cylinders. FN608 is equipped with two independent fuel pumps, each corresponding to a separate left or right fuel rail. If one pump fails, only the corresponding rail is affected while the other side can continue working. FN606 has a single fuel pump, so if that pump fails, the whole system stops working until the pump is replaced.
FN608 和 CT500 有什麼不同？
- FN608 supports 8-cylinder testing, while CT500 supports 6-cylinder testing.
- FN608 has a heating cleaning tank that can maintain up to 50°C, while CT500 does not support heating.
- FN608 supports 12V, 12-70V, and 120-180V voltage ranges, while CT500 supports 12V, 70V, and 120V.
- FN608 also has a cleaning tank that can be used independently or together with the main unit, plus two independent fuel pumps.
- CT500 has an integrated cleaning tank and one fuel pump.
CT150、CT160 和 CT200 有什麼不同？
- Four standard 12 V injectors: CT150; choose CT160 when heated ultrasonic cleaning is required.
- Six standard injectors: CT200 adds two test positions.
- For low-pressure cleaning and testing of compatible GDI high-pressure injectors, compare CT400, CT450, CT500, FN606, and FN608 by supported injector type and test functions.
保固期有多長？
主機：三年保固。標準配件：一年保固。保固政策。
客戶評價
留言
Alvis Gibbon ✓ 已驗證購買 -
Excellent, the cleaning cycle and ultrasonic combination made the three faulty…
Excellent, the cleaning cycle and ultrasonic combination made the three faulty injectors come around – highly recommend this. Great Value for money
Cernty ✓ 已驗證購買 -
I’ve been using the CT400 injector cleaner for 2 months, and it’s a game-changer…
I’ve been using the CT400 injector cleaner for 2 months, and it’s a game-changer for my repair shop. It supports GDI, EFI, and most European and Asian models perfectly. Ultrasonic cleaning is strong, testing is accurate, and the 6-cylinder design saves so much time. Easy to operate, stable performance, and highly recommended for every mechanic!
湯姆 ✓ 已驗證購買 -
CT400 is worth every penny!
CT400 is worth every penny! It handles 12V, 70V, 120V injectors with no issues. The pressure is stable, leakage testing is reliable, and cleaning old injectors back to normal is super easy. My customers notice better engine performance right away. Great machine, fast delivery, excellent quality!