ภาษาและสกุลเงิน
AUTOOL BT160 Automotive Power Circuit Tester
US$33.00
Key Features
- 6–24V Circuit States
- Continuity + Ground Checks
- Controlled Component Activation
- Harness Short Tracing
- 6–24V Circuit States: Identify positive, negative, and open conditions in 6–24 V DC vehicle circuits with red and green LED feedback.
- Continuity + Ground Checks: Check wires, fuses, relays, switches, and component ground paths for continuity or open conditions.
- Controlled Component Activation: Apply power or ground to selected components for in-vehicle or bench checks.
- Harness Short Tracing: Probe successive harness sections after removing a blown fuse to narrow the side carrying a short or overload condition.
- 4 m Working Reach: Reach test points from the vehicle battery with the integrated 4 m lead.
- 3- รับประกันปี ตัวเครื่องหลัก 3 ปี · อุปกรณ์เสริม 1 ปี
- 90-Day Returns สินค้าที่ส่งคืนต้องอยู่ในสภาพสมบูรณ์ภายใน 90 วัน
- ร้านค้าอย่างเป็นทางการ สินค้าแท้ · การสนับสนุนโดยตรง
AUTOOL BT160 · 6–24V Powered Circuit Probe
Probe and Activate Compatible DC Circuits
Trace common faults from the battery to distant test points with this automotive electrical circuit tester for compatible 6–24V DC vehicle circuits. BT160 identifies positive, negative, and open states, checks continuity and ground paths, and can apply controlled power or ground to selected components. Its long integrated lead supports front-to-rear harness work on larger vehicles.
- 6–24 V DC Circuits
- Polarity / Continuity / Ground Checks
- Selected Component Activation
- Manual Short-Circuit Tracing
- 4 m Test Lead
Key Features
Power and Ground Checks with a Circuit Test Probe
การทดสอบขั้ว
Probe an unknown contact to identify circuit polarity. The red LED indicates positive voltage, and the green LED indicates negative voltage.
Continuity And Open Circuit Test
Check whether a tested wire, fuse, relay, switch, or circuit path is continuous or open by using the auxiliary ground lead and probe tip.
โหมดทดสอบไดโอด
Quickly test the working status of a diode assembly and determine whether the circuit is open or continuous.
การทดสอบการต่อสายดิน
Check whether the negative grounding of a component is good. Green LED with buzzer feedback indicates good grounding under the correct test setup.
Short Circuit Following
After removing the blown fuse, probe successive harness sections to narrow which side still shows the short or overload condition.
ระบบป้องกันกระแสไฟเกิน
When overload or excessive current is detected, BT160 automatically opens circuit protection and beeps to reduce unnecessary losses.
6–24V DC Testing
Use BT160 only with 6-24V DC automotive electrical systems, including common 12V cars and 24V heavy trucks.
4m Test Lead
The 4m lead extends working reach from the battery, while the 220 × 30 × 30mm probe body fits in one hand.
Component Activation
Supports component testing both outside the vehicle and in the vehicle electrical system. Follow the specified wiring and activation procedure for the component under test. Apply output only in the documented polarity/current mode; do not inject power or ground into an ECU, SRS, sensor or data line without a specific authorized procedure.
รับประกัน 3 ปี
ตัวเครื่องหลัก: รับประกัน 3 ปี อุปกรณ์เสริมมาตรฐาน: รับประกัน 1 ปีนโยบายการรับประกัน
เวิร์กโฟลว์การบริการ
Connect, Identify and Test the Circuit
ความคืบหน้าทีละขั้นตอน1 / 10
01
Connect To Battery
Unroll the leads. Connect the red clip to the positive terminal of the vehicle battery and the black clip to the negative terminal.
02
Run A Quick Self-Test
Press the switch to confirm LED feedback. Red indicates positive voltage and green indicates negative voltage.
03
Probe The Circuit
Touch the probe tip to the circuit contact, wire, fuse, relay, diode, or component terminal according to the selected test mode.
04
Read LED And Buzzer Feedback
Use LED color, buzzer behavior, and circuit response to identify positive, negative, open, continuous, grounded, overloaded, or shorted conditions.
05
การทดสอบขั้ว
Contact the probe tip to the tested point. A positive contact lights the red LED, while a negative contact lights the green LED.
06
การทดสอบความต่อเนื่อง
Connect the auxiliary ground lead to one side of the tested wire and the probe tip to the other side. Green LED means continuity is present.
07
Component Activation
Use the power switch to apply positive or negative output under the correct setup. Stop immediately if the LED changes color with buzzer feedback.
08
Jumper Lead Operation
The black clip and auxiliary ground lead are directly connected through the unit, allowing BT160 to work as a long jumper test lead in suitable checks.
09
การทดสอบการต่อลงดิน
Use grounding test mode to check whether the negative grounding of a component is good when high current flow requires reliable grounding.
10
Short Circuit Locating
Remove the blown fuse, start from the fuse socket, follow the wiring harness, and check the wire side where green LED with buzzer appears.
การใช้งานที่ปลอดภัย
Limit Powered Tests to Approved Circuits
6-24V DC Only
Use BT160 only with 6-24V DC automotive electrical systems, including common 12V cars and 24V heavy trucks.
Do Not Use On AC Power
BT160 is not designed for 110V / 220V AC household current or any system above 24V DC.
Spark Warning
Sparks may occur at the probe tip during use. Do not operate in areas with combustible gas, dust, or explosive conditions.
ตรวจสอบก่อนใช้งาน
Check the case, probe tip, clips, and leads before use. Do not use the tester if cracks, exposed wires, or visible damage are found.
Sharp Probe Tip
The probe is sharp. Use and store it carefully, and keep the tool away from children.
Do Not Open The Tool
Do not disassemble BT160. Opening the tool voids the warranty, and repairs should be handled by authorized service support.
Interpret the Result in Context
Verify the circuit, mode, polarity and permitted load before applying power or ground. Protection in the tester does not prove that an ECU, sensor, SRS circuit or other sensitive module can accept an active output.
Stop on an Overload Alert
During component activation, an overload can disconnect output and trigger an LED change with a beeping alarm. Stop the test, then check the circuit, component condition, and rated current before continuing.
เปรียบเทียบรุ่น
Choose the Right Circuit Test Tool
คู่มือรุ่น
Choose one or more models. BT160 is selected by default.
เลือก 1 รุ่น
ยังไม่ได้เลือกโมเดล โปรดเลือกโมเดลเพื่อเปรียบเทียบ
| ชื่อสินค้า | BT160 | BT210 | BT250 | BT260 | BT280 |
|---|---|---|---|---|---|
| ช่วงการวัด | |||||
| DC Voltage Measurement Range | × | 9 ~ 30V | 0 ~ 65V | 0 ~ 65V | 0.1 ~ 100V |
| ช่วงการวัดแรงดันไฟฟ้ากระแสสลับ | × | 9 ~ 30V | 0 ~ 65V | 0 ~ 65V | 0.1 ~ 100V |
| ช่วงการวัดความต้านทาน | × | × | 0~200KΩ | 0~200KΩ | 1~200KΩ |
| ช่วงการวัดปัจจุบัน | 0 ~ 10A | 0 ~ 10A | 1 ~ 10A | The 1–10 A figure is a rated-current/protection limit. Choose a model with a documented ammeter mode when current measurement is required. | 0 ~ 18A |
| Core Tests & Protection | |||||
| DC Voltage Detection Mode | ✓ | ✓ | ✓ | ✓ | ✓ |
| การทดสอบการต่อสายดิน | ✓ | × | ✓ | ✓ | ✓ |
| ทดสอบอุณหภูมิ | × | ✓ | × | × | × |
| การทดสอบขั้ว | ✓ | ✓ | ✓ | ✓ | ✓ |
| ระบบป้องกันกระแสไฟเกิน | ✓ | ✓ | ✓ | ✓ | ✓ |
| ทดสอบความต่อเนื่อง | ✓ | ✓ | ✓ | ✓ | ✓ |
| โหมดทดสอบไดโอด | ✓ | × | ✓ | ✓ | ✓ |
| Resistance Detection Mode | × | × | ✓ | ✓ | ✓ |
| Advanced Diagnostics & Output | |||||
| Injector Test | × | × | × | × | ✓ |
| 0~5V Power Supply | × | × | × | × | ✓ |
| Relay Test | × | × | × | × | ✓ |
| Component Activation | × | × | × | × | ✓ |
| Oscilloscope Mode | × | × | × | × | ✓ |
| Multimeter Mode | × | × | × | × | ✓ |
| การทดสอบแบบสมาร์ท | × | × | × | × | ✓ |
| Hardware, Power, Interface & Updates | |||||
| การดำเนินงานแรงดันไฟฟ้า | 6 ~ 24V | 9 ~ 30V | 9 ~ 30V | 9 ~ 30V | 9 ~ 30V |
| ความยาวสายไฟ | 4m | 1.1m | 1.5m | 12m | 6m |
| หลายภาษา | × | × | 9 | 9 | 14 |
| ขนาดหน้าจอ | × | × | 1.65 นิ้ว | 1.65 นิ้ว | 2.8 นิ้ว |
| หน้าจอสี TFT | × | × | ✓ | ✓ | ✓ |
| ไฟ LED | × | ✓ | ✓ | ✓ | ✓ |
| อัพเดทออนไลน์ | × | × | × | × | ✓ |
คู่มือและฝ่ายสนับสนุน
Find the Manual and Connection Guidance
AUTOOL BT160 User Manual
เปิดคู่มือฉบับ PDF สำหรับ AUTOOL BT160 voltage, polarity, continuity, diode and grounding checks, short-circuit tracing, component activation, overload protection and troubleshooting support.
บรรจุภัณฑ์
ดูว่ามีอะไรอยู่ในกล่องบ้าง
- หน่วยงานหลักAUTOOL BT160 automotive electrical system tester
- สายไฟIntegrated 4m / 13ft lead with red and black battery clips
- Auxiliary GroundAuxiliary ground clamp
- เอกสารBT160 user manual
- กล่องขายปลีกAUTOOL BT160 retail package
- ตรวจสอบขั้นสุดท้ายAccessories follow the listed package configuration.
คำถามจากผู้ซื้อ
Circuit Connection and Measurement Questions
Can BT160 Be Used On 12V Cars And 24V Trucks?
Yes. BT160 is designed for 6-24V DC systems, so it is suitable for common 12V car electrical checks and 24V heavy truck electrical checks when used within the specified range.
Can BT160 Be Used On 110V Or 220V AC Circuits?
No. BT160 is not designed for 110V / 220V AC household current or any over-24V DC system. Use it only on 6-24V DC automotive electrical systems.
Does BT160 Measure Exact Voltage Values?
BT160 does not have a screen and is not the right choice for reading exact voltage values. It is intended for quick DC circuit presence, polarity, continuity, diode, grounding, and overload checks. Choose BT210, BT250, BT260, or BT280 if you need numerical voltage display or more measurement functions.
What Do The Red And Green LEDs Mean?
Red LED indicates positive voltage supplied or detected. Green LED indicates negative voltage supplied or detected. In continuity testing, green LED feedback indicates continuity is present.
Does BT160 Support Temperature Test Or LED Light?
BT160 is positioned as a simple 6-24V DC circuit tester and does not list temperature test or LED light as BT160 functions in the model comparison. Choose BT210 if you need temperature test and LED light support.
How Does The Power Switch Work?
The power switch can be used to output voltage during suitable tests.
- Press the “-” side to output positive voltage and press the “=” side to output negative voltage.
- Follow the manual and stop if the LED changes color with buzzer feedback during component testing.
- Use only the documented polarity/current mode and never inject power or ground into an ECU, SRS, sensor or data line without a specific procedure.
What Should I Do If Overload Protection Is Triggered?
If BT160 beeps or the LED changes unexpectedly during a powered test, stop testing immediately. Check whether the tested component is defective, whether the circuit is shorted, or whether the rated current of the component is higher than the tester can support.
What Is Included In The BT160 Package?
Package contents: BT160 main unit, integrated lead with red and black battery clips, auxiliary ground clamp, user manual, and retail box.
ที่ AUTOOL Circuit Tester Should I Choose?
- Choose BT160 if you need a compact no-screen 6-24V DC tester for polarity, open circuit, diode, grounding, and overload protection checks.
- Choose BT210 for a simple digital display, temperature test, and LED light.
- Choose BT250 or BT260 for TFT screen, AC / DC voltage, resistance, and multi-language support.
- Choose BT280 for smart test, multimeter, oscilloscope, relay, injector, component activation, online update, and higher-end diagnostic functions.
การรับประกันนานแค่ไหน?
ตัวเครื่องหลัก: รับประกัน 3 ปี อุปกรณ์เสริมมาตรฐาน: รับประกัน 1 ปีนโยบายการรับประกัน
ความคิดเห็นของลูกค้า
เขียนรีวิว
ยังไม่มีรีวิวร่วมแบ่งปันประสบการณ์ของคุณกับผลิตภัณฑ์นี้ก่อนใคร