언어 및 통화
AUTOOL CT60 Fuel Injector Pulse Tester
US$70.00
주요 특징
- Dual-Injector Signal Output
- 12 V + Instantaneous 75 V Drive
- 600–4,000 RPM Control
- 0–99 Minute Timing
- Dual-Injector Signal Output: Drive two compatible injectors together to compare response, spray shape, and spray angle in a suitable external cleaning or observation setup.
- 12 V + Instantaneous 75 V Drive: Select standard 12 V output or instantaneous 75 V drive for a compatible high-voltage injector.
- 600–4,000 RPM Control: Set a simulated operating range from 600 to 4,000 RPM for controlled response observations.
- 0–99 Minute Timing: Set output duration from 0 to 99 minutes for controlled activation during cleaning or comparison.
- Compact LCD Controller: The 138 × 76 × 30 mm handheld body displays frequency and time close to the work area.
- 3 - 년 보증 본체 3년, 부속품 1년
- 90- 일 반품 90일 이내 반품 가능
- 공식 스토어 정품 · 직접 지원
AUTOOL CT60 · Dual-Output Injector Signal Generator
Drive Two Injectors for Controlled Response Checks
Drive two compatible injectors together with this handheld pulse tester, using a separate approved cleaning or observation setup to compare response and spray behavior. Select standard 12 V or instantaneous 75 V output to match the injector requirement, then adjust simulated speed from 600–4,000 RPM and output time from 0–99 minutes. The LCD and pulse indicator keep settings and activation visible.
- Dual-Injector Pulse Output
- 12 V / Instantaneous 75 V
- 600–4,000 RPM Settings
- 0–99 Minute Output Timer
- Separate Ultrasonic-Tank Companion
주요 특징
Standard and High-Voltage Modes with Dual Outputs
Standard Injector Mode
Use the 12 V output for compatible standard electromagnetic gasoline injectors after confirming the injector requirement.
Compatible High-Voltage Mode
An instantaneous 75 V output helps drive the electromagnetic valve in compatible high-voltage injectors. For a turbocharged application, use this mode only when the injector is confirmed as a compatible high-voltage type.
Wide RPM Adjustment
Set 600–4,000 RPM to compare injector response and spray behavior under controlled simulated speeds.
Adjustable Working Time
Set output duration from 0 to 99 minutes for controlled injector activation during the cleaning, observation, or comparison procedure.
LCD Digital Settings
Read working frequency and time on the LCD so you can record and repeat the same injector-drive settings.
Dual-Injector Output
Drive two compatible injectors together to compare response, spray shape and spray angle under one approved external fluid and observation setup.
Pulse Output Indicator
A working indicator shows when CT60 is sending the injector pulse signal.
Ultrasonic-Cleaning Companion
Use the CT60 to pulse compatible injectors during cleaning with a separate ultrasonic cleaning tank.
Compact Handheld Control
Keep the LCD, setting controls and injector connections close to the work area with the compact 138 × 76 × 30 mm handheld body.
3년 보증 지원
본체: 3년 보증. 표준 부속품: 1년 보증. 보증 정책.
이용 방법
Identify the Injector, Select Mode, Connect, and Observe
단계별 진행 상황1 / 7
01
Identify The Injector
Confirm whether the injector is standard or a compatible high-voltage type and choose the correct connector and observation setup.
02
Prepare A Safe Work Area
Switch off the engine, remove the injector using the vehicle service procedure, ventilate the area and contain fuel or cleaner spray.
03
Connect The Injector
Connect the CT60 pulse lead and approved adapter securely; install the injector in suitable cleaning or test equipment.
04
Power CT60 Correctly
Use the supplied adapter and cables according to the manual; never connect clamp leads to AC mains.
05
Set Mode, RPM & Time
Select the injector mode, then set the same RPM and duration for every comparison.
06
Run & Observe
Start the pulse output and observe actuation, visible spray pattern, angle and unwanted dripping without entering the spray path.
07
Repeat Before A Decision
If a difference appears, reseat connectors and repeat under the same conditions before cleaning, further diagnosis or replacement.
안전성 및 호환성
Confirm Injector Type, Wiring, Voltage Mode, and Duty Cycle
Use It As A Signal Generator
CT60 needs separate equipment to hold the injector and safely manage cleaning or test fluid.
Confirm Drive Compatibility
Match the drive voltage to the injector specification. Confirm the requirement before selecting 75 V.
Control Fuel And Cleaner
Work with ventilation, eye protection and a contained spray path; keep fuel and cleaner away from flames, sparks and hot parts.
Use The Supplied Power Hardware
Follow the manual for the power adapter and cables. Never connect clamp leads directly to 110/220 V AC mains.
Stop On Abnormal Heat Or Damage
Stop immediately if a cable, adapter, connector or injector becomes loose, damaged, hot or abnormal.
Check The Complete Setup
Before buying, confirm injector connector, drive requirement, separate cleaning/test equipment and fluid method.
Compare Injector Response
Use the visible response and spray pattern for matched comparison; use calibrated flow equipment when the job requires measured delivery or OEM limits.
Avoid High-Voltage Parts
Do not touch vehicle parts marked with a dangerous voltage logo.
Use Supplied Electrical Equipment
Use the supplied power adapter and cables only according to the CT60 user manual and local electrical safety rules.
시험 결과
Observe Response Without Claiming Flow Performance
Confirm Actuation First
The pulse indicator plus an audible or visible injector response shows that the control signal reached the setup; no response still requires connector, power and injector checks.
Compare Like With Like
Compare injectors of the same application at the same mode, RPM, time, fluid and fixture position. A repeatable difference is more useful than one isolated observation.
Read the Fuel Injector Spray Pattern
Compare pattern and angle between matched injectors under the same settings, then repeat any irregular response before the next diagnostic step.
Watch For Dripping
Unwanted drops or continued wetting during the approved observation procedure can justify a repeat test and further sealing diagnosis.
Retest After Cleaning
Repeat the original settings after cleaning. Improvement, no change and intermittent behavior are all useful outcomes to record.
Choose the Next Injector Test
CT60 provides pulse control and visual spray comparison. Use calibrated flow or high-pressure equipment for measured delivery, GDI validation or unresolved vehicle faults.
모델 비교
Compare Signal Generators and Test Benches
모델 가이드
Choose one or more options. CT60 is selected by default.
1개 모델이 선택되었습니다.
선택된 모델이 없습니다. 비교할 모델을 선택하세요.
| 태스크 | CT60 | Complete Injector Bench |
|---|---|---|
| Workflow Scope | ||
| 기본 작업 | Injector pulse generation and visual response support | Cleaning, fluid control and comparative measurement, depending on model |
| Fluid system | Requires separate suitable equipment | Built into the bench |
| Simultaneous positions | 2 injector outputs | Model-specific; verify before purchase |
| Allowed conclusion | Visible actuation/spray difference | Model- and method-specific comparison; not automatically OEM certification |
사용 설명서 및 다운로드
설정 및 테스트 모드에 대해서는 설명서를 참조하십시오.
AUTOOL CT60 Manual & Guides
Visit the manual download center to find model-specific CT60 setup, injector-mode selection, RPM and timing controls, electrical safety, and troubleshooting guidance.
묶음
포함 된 것
- CT60 Main UnitFuel injector signal generator with LCD controls.
- 신호 케이블Injector pulse-signal connection cable.
- 클램프 케이블Positive and negative clamp cable for the power connection.
- 전원 어댑터Power adapter for the CT60 setup.
- 커넥터 액세서리Injector cleaning and test connector accessories.
- Documentation And BoxUser manual and CT60 retail box.
자주 묻는 질문
Injector Drive and Connection Questions
Is CT60 a complete injector cleaner and tester?
No. It generates injector pulse signals and must be paired with suitable equipment that handles cleaning fluid or spray observation.
Which injectors can CT60 drive?
It provides a 12 V standard mode and an instantaneous 75 V mode for compatible high-voltage injectors. Confirm the exact injector requirement before use.
Can it compare two injectors?
Yes. Two compatible injectors can be driven together under the same setup for a visual response and spray comparison.
Does it measure injector flow?
No. CT60 supports visual response and spray-pattern comparison. Choose a calibrated injector bench when measured flow is required.
What can I adjust?
The LCD controls 600–4,000 RPM and 0–99 minutes, along with the injector drive mode.
Can CT60 pulse injectors during ultrasonic injector cleaning?
Yes, with a separate suitable ultrasonic setup, compatible connector and approved cleaning method.
How do I power it safely?
Use the supplied adapter and correct cables according to the manual. Never connect clamp leads directly to AC mains.
What does an uneven spray prove?
Repeat the observation under the same settings. If the difference remains, continue with calibrated flow, electrical or on-vehicle testing as the job requires.
보증은 무엇입니까?
본체: 3년 보증. 표준 부속품: 1년 보증. 보증 정책.
How Do I Observe The Injector Spray Pattern?
Prepare and connect the injector safely, select its verified drive mode, set RPM and working time, and use suitable cleaning or test equipment to observe response, spray pattern, and spray angle.
What Safety Precautions Should I Follow?
Turn off the engine, keep fuel away from heat and flame, ventilate the work area, avoid rotating, hot, and high-voltage parts, and wear qualified safety goggles.
What Is Included In The CT60 Package?
Package contents: CT60 main unit, signal cable, clamp cable, power adapter, connector accessories, user manual, and retail box. Check the contents of the selected package before ordering.
고객 리뷰
리뷰 남기기
Ternence Hobson ✓ 구매 확인 완료 -
Cleaned 12 injectors so far, tool is working good.
Cleaned 12 injectors so far, tool is working good. No issues, worth the money. Unstuck and cleaned some of my old spare Nissan injectors.
Lesley Sapir ✓ 구매 확인 완료 -
훌륭하게 일했다
So far it’s worked great we were able to get some injectors cleaned and working again with this tool
Lesley Sapir ✓ 구매 확인 완료 -
훌륭하게 일했다
So far it’s worked great we were able to get some injectors cleaned and working again with this tool